MTD K-Style Betreibershandbuch

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • WarrantyL600-Series Snow Thrower m K StyleMTD LLC, P.O. BOX

Fuel RecommendationsUse automotive gasoline (unleaded or low leaded to minimizecombustion chamber deposits) with a minimum of 87 octane.Gasoline with

AdjustmentsSkidShoesThe snow thrower skid shoes are adjusted upward at the factoryfor shipping purposes. Adjust them downward, if desired, priorto ope

AugerControlWARNING! Prior to operating your snow thrower,carefully read and follow all instructions below.Perform all adjustments to verify your snow

Controlsand Features4DriveShift LeverDirectional Control)_======Auger ControlChute AssemblyGas Cap,Heated GripsClean OutToolAugersShoePrimer K_yJ o_Ch

ThrottleControlThe throttle control is located on the rear of the engine. Itregulates the speed of the engine and will shut offthe enginewhen moved in

ChuteDirectional Control[PUSH BUTTONiCHUTEROTATELEFT[PUSHRUTTU. CHUTEROTATERIGHTThe chute directional control is located on the left side of thedash p

OperationStarting the Enginel_lhllL ARNING! Always keep hands and feet clear ofmoving parts. Do not use a pressurized startingfluid. Vapors are flamma

RecoilStarterCAUTION: Do not pull the starter handle while theengine running.WARNING! To avoid unsupervised engineoperation, never leave the engine un

Maintenance& Adjustments6MaintenanceEngineRefer to the Engine Maintenance section.ShavePlate and SkidShoesThe shave plate and skid shoes on the bo

AugerShaftAt least once a season, remove the shear pins from the augershaft. Spray lubricant inside the shaft and around the spacers andthe flange bea

ToTheOwner1ThankYouThank you for purchasing a Snow Thrower manufactured byMTD LLC. It was carefully engineered to provide excellentperformance when pr

DriveControlWhen the drive control is released and in the disengaged "up"position, the cable should have very little slack. It should NOT be

EngineMaintenance7WARNING! To prevent accidental start-up, shut offthe engine and remove the key before performingany type of engine maintenance.Perio

6. Refill with the recommended oil and check the oil level;refer to Operation section for instructions.7. Reinstall the oil filler cap/dipstick secure

Cleaningthe EngineIf the engine has been running, allow it to cool for at least halfan hour before cleaning. Periodically remove dirt build-up fromeng

ServiceBelt ReplacementAuger BeltTo remove and replace your snow thrower's auger belt, proceedas follows:I. Allow the engine to run until it is o

7. Drive BeltRemove the belt from around the auger pulley, and slip thebelt between the support bracket and the auger pulley.See Fig. 8-5.Figure 8-58.

6.Back out the stop bolt to increase the clearance betweenthe friction wheel disc and friction wheel. See Fig. 8-7.//Figure 8-77. Slip the drive belt

5_Carefully remove the hex nut which secures the hex shaftto the snow thrower frame and lightly tap the shaft's end todislodge the ball bearing f

Troubleshooting928ProblemEngine fails to startEngine running erratically/inconsistent RPM (huntingCauseor surging)1. Choke notin CHOKE position.2. Spa

ReplacementParts1Component l Part Number and Description929-0071Extension Cord, 110V954-04050 Auger Drive Belt954-0367 Wheel Drive Belt684-04153935-04

ImportantSafeOperationPractices2WARNING! This symbol points out important safety instructions which, if not followed,could endanger the personal safet

Attachments& Accessories11The following attachments and accessories are available for your snow thrower. Phone (800) 800-7310 for information rega

1231

SECTION12-- NOTES

SECTION12 -- NOTES 33

MTD CONSUMER GROUP INC (MTD), the California Air Resources Board (CARB)and the United States Environment Protection Agency (U. S. EPA)Emission Control

(4)Repairorreplacementofanywarrantedpartunderthewarrantyprovisionsofthisarticlemustbeperformedatnochargetotheowneratawarrantystation.(5)Notwithstandin

MANUFACTURER'S LiMiTED WARRANTY FORThe limited warranty set forth below is given by MTD LLC withrespect to new merchandise purchased and used in

SafeHandling of GasolineTo avoid personal injury or property damage use extreme carein handling gasoline. Gasoline is extremely flammable and thevapor

Clearinga CloggedDischargeChuteHand contact with the rotating impeller inside the dischargechute is the most common cause of injury associated with sn

Safety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on themach

Assembly& Set-Up3Contentsof CartonOne Snow ThrowerOne Snow Thrower Operator'sManualTwo Replacement Auger Shear PinsHex RodOne Product Registr

3.4.Place chute onto chute base and ensure hex rod ispositioned under the handle panel. Install hex boltpreviously removed but do not secure with wing

7 Set-UpPush the hex rod toward the control panel until the holein the hex rod lines up with the hole in the chute controlinput closest to the chute c