MTD E173 Betreibershandbuch

IMPORTANT: Read safety rules and instructions carefully before operating equipment.MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722Single

10SECTION 6: MAINTAINING YOUR SNOW THROWERWARNING: Before servicing, repairing, orinspecting, disengage all clutch levers andstop engine. Wait until

11SECTION 8: TROUBLESHOOTING GUIDENOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized servicerepresentative

12SECTION 9: PARTS LIST FOR MODEL SERIES 140 THROUGH E173722104637313413213833035627394012014635306528254542134472233917181542112619261632231236418

13Model Series 140 Through E173Ref. No. Part No. Part Description1.710-0167 Carriage Bolt2.710-0276 Carriage Bolt3.710-0323 Pan Head Screw4.710-0451 C

14Models 140, 150, E150 and E151 Ref. No. Part No. Part Description1.710-1270 Oval C-Sunk Screw2.710-0487 Carriage Bolt3.712-0324 Lock Nut4.720-0284 H

15Model Series 14012345678910111213414Ref. No. Part No. Part Description1.710-0157 Hex Screw 5/16-24 x 0.75”2.710-0805 Hex Screw 5/16-18 x 1.5”3.710-1

16Ref. No. Part No. Part Description1.629-0236 Extension Cord *Electric start models only2.705-5139A Support Bracket: Gas Tank3.710-0157 Hex Screw 5/1

17Models 140 and E142Ref. No. Part No. Part Description1.684-0056 Dash—21"2.710-1090 Hex Flange Screw 3.710-0895 Hex Tap Screw4.710-1268 Hex Tap

18Model Series 150 and E1501823456791011121314151617192055523238222120551826258248Ref. No. Part No. Part Description1.684-0126 Chute Crank Assembly2.6

19Models E160 through E172Ref. No. Part No. Part Description1.684-0126 Chute Crank Assembly2.684-0160 Dash Assembly3.710-1003 Special Screw4.710-1090

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices ... 3A

MANUFACTURER’SLIMITED WARRANTYThe limited warranty set forth below is given by MTDPRODUCTS INC (“MTD”) with respect to new merchan-dise purchased and

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger t

46. Do not operate machine while under the influence of alcohol or drugs. 7. Muffler and engine become hot and can cause a burn. Do not touch.8. Exe

5SECTION 2: ASSEMBLING YOUR SNOW THROWERUnpacking From Carton• Cut along corners of the carton and lay it down flat. See Figure 1. Remove packing mat

6• Lift the control handle up, and hook the “Z” end of the control cable into the bottom hole in the control handle, from the outside to the inside .

7SECTION 3: KNOW YOUR SNOW THROWERBe familiar with all the controls and their proper operation. Know how to stop the machine and disengage them quick

8SECTION 4: OPERATING YOUR SNOW THROWERBefore StartingWARNING: Read, understand, and followall instructions and warnings on the machineand in this ma

9SECTION 5: MAKING ADJUSTMENTSWARNING: NEVER attempt to make anyadjustments while the engine is running, exceptwhere specified in the operator’s man