MTD E660F Betreibershandbuch

OPERATOR'S MANUALSNOW THROWERMODELSE600E, $610EE640F, E660FE660G, E6COFIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWarning: This unit

Traction/AugerControl Lock .-------.=Discharge ChuteChuteClean-out ToolAugerShift LeverAuger Controlf\Chute Directional Control_.=_Spark PlugChoke _ ,

Attach spark plug wire to spark plug. Make certainthe metal loop on end of the spark plug wire (insidethe boot) is fastened securely over the metal ti

ToEngageDrive• With the engine running near top speed, move shiftlever into one of the five FORWARD positions ortwo REVERSE positions. Select a speeda

DriftCutters(Optional Equipment)Drift cutters should be used when operating the snowthrower in heavy drift conditions.On models so equipped, drift cut

• With traction control engaged, the friction wheelmust contact the drive plate. See Figure 15.FrictionWheelGear ShaftDriveFigure 15If adjustment is n

DriveWheelsThe wheels may be adjusted for two different methodsof operation. The adjustment is made by placing theclick pins in one of two different h

Wheels• Oil or spray lubricant into bearings at least once aseason. Pull the klick pins and remove wheels,clean and coat axles with a multipurposeauto

• Roll the front and rear auger belts off the enginepulley. See Figure 22.Rear Auger _ J_ f-- -- DriveBelt _ ,- _ f==_.._ Belt Engine' " -0&

• Using a wrench to hold the shaft, loosen, but do notcompletely remove, the hex nut and bell washer onleft end of gear shaft. See Figure 25.• Lightly

SECTION9: TROUBLESHOOTINGGUIDETroubleEnginefails to startEngine runs erraticLoss of powerEngine overheatsExcessive vibrationUnit fails to propelitself

TABLEOFCONTENTSContent Pageimportant Safe Operation Practices ... 3Loose Parts &a

SECTION10: PARTSLIST33\3918161/I 235217181/!61 63626445442730313753\52545742545556595O582O

ModelsE6OOE,$610E,E640F,E660F,E6COF&E660GREE PARTNO. NO.1 714-05072 747-08773 710-05994 784-56805 784-56796 748-03627 748-03638 732-01459 711-0653

ModelsE6OOE,$610E,E640F,E660F,E6COF&E660G2039 3837J14263628137564Drive Clutch CableAuger Clutch Cable330449 108415Auger Clutch Cable35I1 122

ModelsE6OOE,$610E,E640F,E660F,E6COF&E660GREE PARTNO. NO.1 710-16522 784-56883 784-5687A4 756-06255 738-09246 784-5630B7 741-05638 736-01059 712-01

ModelsE6OOE,$610E,E640F,E660F,E6COF&E660G11 1014 121938211341l 18_1826223942REF.NO.1234567891011121314151618192021222325PARTNO.712-0116756-0178784

ModelsE6OOE,$610E,E640F,E660F,E6COF&E660G©REF. PARTNO. NO.1 618-01232 618-01243 710-06424 711-0908A711-0909A711-0910A5 714-01616 715-01437 717-052

ModelsE6OOE& $610EIMPORTANT: For a properly working machine, use Factory Approved Parts.V-BELTS are specially designed to engage and disengage saf

ModelsE640F,E660F,E6COF& E660GiMPORTANT: For a proper working machine, use Factory Approved Parts.-BELTS are specially designed to engage and dise

MANUFACTURER'S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTD LLC withrespect to new merchandise purchased and used in

SECTION1: IMPORTANTSAFEOPERATIONPRACTICESThis symbol points out important safety instructions,which if not followed, could endanger the personalsafety

4. Neveroperatewithamissingordamageddischargechute.Keepallsafetydevicesinplaceandworking.5. Neverrunanengineindoorsorinapoorlyventilatedarea.Engineexh

ContentsOfHardwarePackLay out the hardware according to the illustrationfor identification purposes. Part numbers are shown inparentheses. (Hardware p

SECTION2: ASSEMBLINGYOURSNOWTHROWERLoosePartsFigure 1 shows parts of the snow thrower packed loosein the carton. You will need these parts along withh

CuppedBoltsLock NutsFigure 3Tighten the four hex bolts used earlier to attachbottom of the handles to the snow thrower frame.See Figure 2.AttachingCon

After assembling all three chute flange keepers,tighten, then back off 1/4 turn to allow easiermovement of the chute. Use two 7/16" wrenches.Atta

-Shift RodShift ArmAssemblyj Hairpin ClipFigure 9LampWiringNOTE: A lamp is an optional feature of some modelsnow throwers and is NOT standard equipmen