MTD 464 Betriebsanleitung PDF herunterladen (Seite 52)

ARMY TM 9-6115-464-34

AIR FORCE 35C2-3-445-2

NAVY NAVFAC P-8-624-34

(9)

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

Remove nuts (14), Iockwashers (15), screws

(18).

(16) and flat washers (17) to remove right relay table

Remove nuts (19), Iockwashers (20), screws (21) and flat washers (22) to remove left relay table

(23).

Remove screw (24), Iockwasher (25) and access cover (26).

Remove screws (27), Iockwashers (28), and air inlet screen (29).

Install engine support bracket (30), flat washer (31), Iockwasher (32) and nut (33).

Remove screws (34), Iockplates (35) and pressure plates (36).

Remove eyebolt (37), from generator set tool box and install into generator.

CAUTION

Do not use a lifting device of less than 1000 lb. capacity. Failure to observe this caution

could result in damage to the equipment.

Attach a lifting device to generator lifting eyebolt.

Remove screws (38), Iockwashers (39), nuts (40), Iockwashers (41), screws (42) and flat washers

(43).

Carefully lift generator while moving it to the rear until coupling disc clears engine flywheel housing.

CAUTION

Do not use a lifting device of less than 1000 lb. capacity. Failure to observe this

caution could result in damage to the equipment.

b. Installation.

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

Attach a lifting device to generator lifting eye bolt.

Carefully lift generator and lower it ilntiel coupling disc engages engine flywheel housing.

Install flatwashers (43, figure 2-2) screws (42) and torque screw to 200-220 ft-lb, Iockwasher (41),

nut (40) and torque to 200-220 ft-lb, Iockwashers (39), and screw (38).

Remove eyebolt (37), from generator and install into generator set tool box.

Install pressure plates (36), Iockplates (35), and screws (34). Torque Iockplate attaching screws (34)

to 120 ft-lb.

Remove nut (33), Iockwasher (32), and flat washer (31) from engine support bracket (30).

Install air inlet screen (29), Iockwashers (28), and screws (27).

Install access cover (26), Iockwasher (25), and screw (24).

Position left relay table (23), to install flat washers (22), screws (21), Iockwashers (20), and nuts (19).

Position right relay table (18), to install flat washers (17), screws (16), Iockwashers (15) and nuts

(14).

Position top relay table (13), to install standoff (12), flat washers (11) Iockwashers (10), and screw

(9).

Install flat washers (8), Iockwashers (7), and screws (6).

2-18

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 492 493

MTD 464 Betriebsanleitung Seite 52

Kommentare zu diesen Handbüchern

MTD 464 Betriebsanleitung Seite 52

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Gartenschredder MTD 464