Mtd 241-521-000 Bedienungsanleitung PDF herunterladen (Seite 8)

OPERATION

INITIAL PREPARATION

1. Place the log splitter on a firm, level surface.

2. Service engine with gasoiine and oil as in

structed in the separate engine manual packed

with your log splitter.

3. Lubricate the beam area where splitting wed je will

slide with engine oil (DO NOT USE GREASE).

Make certain to oil both front and back of the beam

face.

4. Fill the reservoir tank as follows.

a. Remove reservoir vent plug. See figure 11.

Using Oexron II automatic transmission fluid,

or 10W non-foaming hydraulic fluid, fill reser

voir to the top. Replace vent plug secu ely.

b. Disconnect the spark plug wire. Prim a the

pump by pulling the recoii starter, to tu n the

engine over, approximately 10 times. F econ-

nect the spark plug wire.

c. Start engine. Use the control handle to e<tend

the wedge to the far extended position. Leave

the wedge in this position (do not retract).

d. Refill tank to within IVi" to 2" from the op of

the tank. Total capacity of system is ap prox-

imately 4 gallons.

e. Now retract the wedge. Extend and retra :t the

wedge fully 10 to 12 complete cycles to re move

trapped air in the system (system is ‘self

bleeding”).

f. Refill the reservoir to within IV2" to 2" from

the top of the tank. Much of the origina fluid

has been drawn into the cylinder and hcses.

Make certain to refill the reservoir, to pr jvent

extreme damage to the hydraulic pump. F allure

to refill the tank will void your warrants.

NOTE: Some fluid may overflow from the vent pi jg as

the system builds heat and the fluid expands and jeeks

its own level.

WARNING: Do not operate the log splitter

without the proper amount of transmission

fuild in the reservoir tank.

BEFORE STARTING

Before each use, check the following:

1. Place log splitter on a firm, level surface. For ver

tical operation, pull the locking rod out and pivot

it down to release the beam. Place the beam in the

vertical position.

2. Remove the vent f^ug and check the fluid level.

Fluid level should be 1V2" to 2" from the top of the

tank.

IMPORTANT: Reservoir tank must be full as instructed.

Low fluid level will damage the pump and void your

warranty.

3. Lubricate the beam area where splitting wedge will

slide with engine oil (DO NOT USE GREASE).

Make certain to oil both front and back of the beam

face.

4. Fill gasoline tank as instructed in separate engine

manual.

5. Attach spark plug wire to spark plug.

TO START ENGINE

1. Place throttle control lever on the engine in FAST

position. See figure 12.

2. Place choke lever in CHOKE position (a warm

engine may not require choking).

3. Grasp starter handle and pull rope out slowly until

engine reaches start of compression cycle (rope

will pull slightly harder at this point). Let the rope

rewind slowly.

WARNING: When restarting a warm

engine, keep away from muffier and other

heated surfaces on the engine.

4. Puli rope with a rapid, continuous, full arm stroke.

Keep a firm grip on the starter handle. Let the rope

rewind slowly. Do not let starter handle snap back

against starter.

5. Repeat preceding instructions 3 and 4 until engine

fires. When engine starts, move choke lever

halfway between CHOKE and RUN.

6. Move throttle control lever to IDLE position for a

few minutes warm-up. Gradually move choke lever

to RUN position as engine warms up.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 17 18

Kommentare zu diesen Handbüchern

Keine Kommentare

Mtd 241-521-000 Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Mtd 241-521-000