MTD E150 Betreibershandbuch

Operators ManualModel Series140 thru E173Single StageSnow ThrowersModel 150 shownIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWarning: This

SNOW THROWER OPERATING CONTROLSModel 140AugerControlHandleModel 140(w/ Optional Ext. Models 150,151Chute Crank)AJger 1Control_'4andle_. ChuteMode

SECTION 7: OPERATIONWarning' Observe all warning labels on the snow thrower prior to use. See Section 1.FUEL MIXTUREImportant: Mix oil with gasol

SECTION 8: ADJUSTMENTSWARNING: NEVER attempt to clean chute or make any adjustments or repairs while engine isrunning,SHAVE PLATE ADJUSTMENTI,/Augers

SECTION 9: MAINTENANCEWARNING: NEVER attempt to clean chute or make any adjustments or repairs while engineis running,NOTE: Check engine and snow thro

SECTION 10: OFF-SEASON STORAGEWARNING: Never store engine with fuel in tank indoors or in enclosed, poorly ventilatedareas where fuel fumes may reach

Models140150E150E151REF. PARTNO. NO.1 710-12702 710-04873 712-03244 720-02765 725-01576 _746-08837 1747-09468 i749-07059 1736-0451DESCRIPTION:Screw--O

Models 140 thru E173//Cable Spring in16

Models 140 thru E173PARTNO. NO.1 710-01672 ,710-02763 1710-03234 j710-04815 1710-06426 1710-10057 [710-07738 710-08969 710-301510 711-0848A11 712-0429

Models 140 and E142/\\\/EngineC)®RE_ ! PARTNO. NO1 -684-00562 710-08053 710-08954 710-12685 712-02526 712-30107 714-01048 715-01389 720-0201A10 725-02

Models 150, E150, E1731/RER _ PARTNO. NO1 710-08052 _710-10053 710-10034 710-12685 '712-02526 712-30107 714-01048 714-05079 715-013810 720-0201A1

SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOTFOLLOWED, COULD ENDANGER THE P

Models E151, E172,Shtpp_KIREF, - PART _-NO.i NO I1 784-5572 JDash DESCRIPTION2 710-0805 IScrew--Hex Cap3 710-1005 Screw--Hex Washer4 7"10-1003 Sc

Models 140, E142IITightening Torque:150-130 in. Ibs."-FIEF. i PART iNO. i NO _ DESCRIPTION1 7i0-0157 --| Screw--Hex Cap2 710-0805 /Screw--Hex Cap

Mode1150Tightening Torque;lS0-300 in. Ibs.REF.T PART -NO. NO. DESCRIPTION1 705-5139 Bracket - Supped Gas Tank i2 710-0157 Screw - Hex Cap 14 710-0289

Models E150, E151, E152, E172, E173Tightening Torque:150-300 in. Ibs.@REF. PARTNO. NO--t 629:0z362 705-51393 710-01575 710-02896 710-08967 710-10038 7

MANUFACTURER'S LIMITED WARRANTY FOR:YA.. c,,N s)[(For TWO YEARS from the date of retail purchasewithin the United States of America, its possessi

• If the snow thrower should start to vibrate abnormally,stop the engine and check immediately for the cause.Vibration is generat)y a warnin Oof troub

SECTION 2: FINDING YOUR MODEL NUMBERThis Operator's Manual is an important part of your new snow thrower, it will help you assemble, prepare andm

SECTION 4: UNPACKING INSTRUCTIONS• See Figure 3.• Remove staples, break glue on the top flaps of the carton or cut tape at carton end and peel along t

RAISING THE UPPER HANDLE1. Loosen the hand knob on each side of the handle. Bee Figure 4. Remove packing material (if any).2. Squeeze the control hand

INSTALLING THE CHUTE CRANK(Models with Optional Extended Chute Crank only.)On some units, the chute crank can be installed and secured from the top si

SECURE FROM THE UNDERSIDE.See Figure 8.1. Place a piece of the cardboard from the carton on a level sudace, Tip the snow thrower forward so that theho

FUEL AND OIL MIXTUREWARNING: Handle gasoline carefully. Remember that It Is highly flammable. Never fill fueltank indoors, when engine is running or w